Posts Tagged ‘Air Conditioning Maintenance’

What is Refrigerant Pressure and Why Does it Matter? A Question from Beaumont

Wednesday, October 26th, 2011

Refrigerant is often called the “lifeblood” of mechanical cooling devices such as the refrigerator and air conditioner in your Beaumont home. Various heating and cooling (HVAC) components require different operating pressures to move refrigerant and process the refrigeration cycle.

In a nutshell, the refrigeration cycle involves refrigerant, which changes from a liquid to a vapor and back to a liquid again by the addition of pressure and heat. In a refrigeration system, pressurized refrigerant passed through an expansion valve into an evaporator and pressure is reduced. The evaporator is a tube which passes by the area to be cooled. When the pressure drops, this liquid refrigerant changes into a vapor, which absorbs vaporized heat from the area around the evaporator. After the heat is absorbed by the refrigerant, it flows to a condenser, where it passes over coils, absorbs heat from the hot vapor, and condenses back into a liquid. The liquid is returned to the compressor and the cycle begins again.

Today’s refrigerants – especially those used in residential applications – are broken down into two different types, labeled R-22 and R-410A. R-22 is made up of a chlorofluorocarbon (CFC) chemical, which has been found to be damaging to the Earth’s ozone layer. It has been replaced by R-410A, which is made up of a hydrofluorocarbon (HFC) chemical and will eventually be phased out by the year 2020. One of the biggest differences between the two are their operating temperatures. HFCs operate at much higher refrigerant pressure.

This change between refrigerants has created some interesting dynamics and challenges for the HVAC trade. Gauges used to check pressure readings have all changed. And mechanical compressors do not operate with a variety of refrigerants, so the compressors and coils need to be swapped out, too. To give you an example, let’s say you are shopping for a new central air conditioner. Chances are, the new air conditioner will run on R-410A. Your old air conditioner ran on R-22. In order to “match” the compressor in the your new air conditioning unit to the existing indoor coil, you will need to replace the coil and the lines running from your outdoor condensing unit to your indoor air handling unit, which is mounted to your furnace.

You don’t have to understand the refrigeration cycle to know that today’s high-pressure HFC refrigerants require different test instrumentation and retrofitted or upgraded mechanical equipment. The change in operating pressure is a small price to pay for a safer and “green” environment.

Tags: , , , , , ,
Posted in Air Conditioning | Comments Off

Cleaning Air Conditioners: A Guide from Pinewood

Monday, October 17th, 2011

One of the best things you can do to help maintain high indoor air quality in your Pinewood home is to clean your air conditioning system on a regular basis. While these systems make it possible to endured a long, hot year with minimal discomfort, they can also become a breeding ground for bacteria, mold and other indoor air contaminants that can make you sick or cause other types of problems.

Improving your indoor air quality isn’t the only reason you should worry about keeping your air conditioning system clean. A properly maintained air conditioner will function more efficiently for a longer period of time.

Air Filters

Changing or cleaning out your air filters regularly is one of the easiest and most important parts of air conditioner maintenance. These air filters are your number one line of defense against all manner of indoor air pollutants, but if they become saturated, they can no longer do their job. Fortunately, changing out these filters is a quick and easy job. Just mark the date on your calendar so you don’t forget.

Cooling Coils

The cooling coil is another part of your air conditioning system that needs to be cleaned on a regular basis. If your cooling coil is dirty, it won’t actually affect your indoor air quality, but it will impede your air conditioner’s ability to function effectively. The more sediment and debris allowed to build up on your air conditioner’s cooling coil, the less efficiently it will cool the air that passes over it. And if it can’t cool the air properly, your air conditioner will have to work overtime to maintain a comfortable temperature inside your home.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

When Should You Check Your AC Filters: Some Advice from Dayton

Monday, October 10th, 2011

The filters on your air conditioning unit are vital for keeping out the dust and debris that make things like illness, allergies and air quality worse. And it’s important that you take personal responsibility for checking those filters. Sure, you have a Dayton professional visit your home once a year to check the air conditioning, but you should also check the system yourself on a semi-regular basis for possible filter degradation.

Monthly Checks

So, how often should you check? Think of it this way. There is no such thing as checking too much, but you can easily not check often enough. So, we recommend checking your filter at least once every 4 weeks. It may not always need to be changed during that four week checkup (sometimes it can last 6 weeks or longer), but it’s good to take a peek.

Why is this so important? Because filters that haven’t been checked and changed as needed have a habit of building up excess sediment and debris. Not a problem when it comes to actually working, but a huge problem when it comes to your energy bill. The harder a system has to work to keep you house cool, the more energy it draws and the more you pay to have cool air in your home. And it will break down much faster as a result of overwork and dirty filters.

Changing an AC Filter

If your filter is ready for a swap, here are some quick tips to get the job done:

  • Find Your Filters – If you don’t know where your filters are, ask your contractor on the next visit or look near the return grills by the thermostat.
  • Remove the Filters – Open the latches and pull the old filter out to check it. You should be able to see clearly through a permanent filter and a disposable one should still be white. If this isn’t the case, it’s time for a cleaning/replacement.
  • Clean the Area – Clear the grill and area of any debris and sediment that might make the filter worse after replacement.

Proper filter maintenance only takes five minutes and it will save you money every month you run your AC – not a bad deal for a few minutes’ work.

Tags: , , , , ,
Posted in Air Conditioning | Comments Off

Why Are Cleans Filters So Important to AC Efficiency? A Question From Silsbee

Wednesday, September 14th, 2011

Air conditioners cost a lot of money to operate in Silsbee – especially when they don’t work at 100% efficiency. So, it is important to perform the various regular maintenance tasks that ensure the system uses as little electricity as possible. The first thing on your list (and the easiest) is cleaning those filters.

Keeping Filters Clean

The Department of Energy’s Energy Savers website states that you can reduce your air conditioner’s energy consumption by as much as 15% simply by keeping the air filters clean. Why do they matter so much? Consider the nature of a filter.

The filter on your AC unit is designed to capture any dust, debris and sediment in the air supply. If that dust and sediment was allowed in, not only would it gum up the mechanical workings of the device, it would get into your ductwork and reduce the air quality of your home. So, filters are used to capture such things. However, when a filter gets clogged, the system must work harder to draw the air in. As it works harder, the motor turns faster and more electricity is used.

It takes very little to clog the filter of an AC unit, especially if it is running 24 hours a day for two or three months out of the year. So, it’s best to check your filters once every 30 days regardless of what type of filter you are using.

Which Filters to Check

The main filter on your AC unit should be checked along with any air handler filters and any air cleaner filters you have installed in your system. Another thing to consider is the condition of your home and the area around your outdoor condenser. If you have pets, lots of plants or your condenser is located in a dusty area, you may need to check and change those filters even more often.

Most filters are located along the return length of the ductwork – sometimes in ceiling ducts and walls, though they may also be located in your furnace’s air handler or inside the air conditioning unit. If you have window units or mini splits, the filters are frequently in the unit.

Clean air filters are important for your health, your wallet and the longevity of your AC system. Stay on top of them and you will save money in more ways than you might expect.

Tags: , , , , ,
Posted in Air Conditioning | Comments Off

Breakdowns – How to Handle an Overloaded AC in Gilchrest

Monday, September 12th, 2011

The last thing you need on a hot summer day in Gilchrest is for your air conditioner to suddenly cut out. Without the cooling power it provides, your house will get uncomfortable quickly. Fortunately, once you know why this happens, there are several things you can do about it.

Why Air Conditioners Cut Out

The most common reason for air conditioner failure is an overabundance of pressure in the unit. This happens because the coil gets too hot, causing the pressure to rise in the entire device. As the pressure rises past a certain point, an automatic safety shutoff system is engaged. If you can stop the coil from heating up to this point, you can keep your air conditioner running.

How to Keep Them Running

Of course, this is easier said than done. Since your condenser unit with the coil inside is located outside in the heat, it’s only natural for it to get hot during the day – especially an extra hot day when you’re using your air conditioner a lot. You also need to be careful not to put anything over or up against your outdoor condenser unit.

While this may block the sunlight, it will also keep heat in the system and prevent the air conditioner from removing exhaust naturally. So in order to keep your air conditioner as cool as possible, make sure there is nothing up against the vents or impeding air flow in any way. Once you’ve done this, try and find a way to provide shade for you air conditioner without placing objects near the device. Blocking out direct sunlight is the best way to keep your air conditioner cool as long as you can do it without interfering with the system’s natural air flow.

Getting it Back On

If your unit does cut out on you, don’t despair. The best thing to do is to wait about a half hour to give your unit a chance to cool off on its own. Then, spray the coil and other overheated areas with a fine mist of cool water. This should lower the temperature enough that the system can come back on without any further complications.

If the problem persists despite the work you’ve done to keep it cool, you may want to call in a professional to take a look and make sure nothing is broken or worn inside to cause the overloads. Most of the time a little maintenance will take care of the problem, but if not, you’ll want to get repairs done quickly to avoid a full breakdown.

Tags: , , , , ,
Posted in Air Conditioning | Comments Off