Posts Tagged ‘Heating Repair’

Rye Heating Repair Tip: Causes of Delayed Furnace Ignition

Friday, January 6th, 2012

Delayed ignition is usually accompanied by a loud banging or booming sound that resembles a small explosion in your gas appliance. In your Rye home’s furnace, this can be terrifying and should never be ignored.

What Causes Delayed Ignition

Delayed ignition usually happens when you first turn on your furnace, often after a long delay between use, so usually early in the fall or late in the spring when you don’t necessarily have it on every day of the week.

What happens is moisture builds up over the course of a period of inactivity and begins to corrode the firebox in your furnace. That corrosion builds up to the point that it starts to block the ports that feed gas into the burners. When these ports get blocked, the burners down the line cannot light and when you flip the switch, they won’t light immediately.

Of course, while rust and corrosion are a risk, lint and dust can be equally problematic (and are more common if you don’t have your furnace cleaned properly each fall). Sulfur build up is also a possibility, as it is left behind by burning natural gas. It will appear as a layer of white on the surface of the burners or the pilot light.

When all of this happens and the ports are not cleaned properly, gas will build up in the chamber after it is turned on and, when it finally ignites, create the small boom sound. It doesn’t just sound like an explosion – it is one – and if ignored, it can become incredibly dangerous.

Solving the Problem

Delayed furnace ignition is an easy problem to avoid. All you need to do is have your furnace cleaned properly before turning it on each fall. A technician will clean the burners and ports and remove any dust, lint, rust or sulfur buildup that might block ignition and cause a delay.

When replacing your furnace, look for a device with corrosion resistant materials. You can learn more about these when it comes time to replace your furnace from a technician. Most importantly, be careful. It may be a small problem now, but if left to build up over time, that small boom can become a much larger one.

Tags: , , , , , ,
Posted in Heating | Comments Off

Batson Heating Tip: What Does a Furnace Fan Limit Switch Do?

Monday, January 2nd, 2012

When researching your Batson home’s furnace and potential problems it might have, you’ve probably run across a few references to the fan limit switch. And while you know that it can break in a number of ways, do you know what the switch does and what you should look for when checking your furnace its air handler for problems?

What the Limit Switch Does

To put it very simply, the furnace fan limit switch is a control that tells your furnace’s fan when to turn on and off. So, when the furnace isn’t on, it tells the blower not to operate (and send cold air into your home) and when the furnace is on, it tells the blower to turn on and start circulating the warm air.

While the primary function of the limit switch is to turn the blower fan on and off, it also has a safety role. When the temperature in the air supply plenum gets too hot, the limit switch turns off the furnace boiler to keep there from being any damage from overheating. This is handy if there is a blockage in the air vents or the controls are messed up due to water damage or improper adjustments to the settings.

Looking for Problems

Most of the time, when there is an issue with your furnace turning off or on frequently, the limit switch is one of the first things you will check. Because the switch is electronic and is attached to a thermostat which measures temperature in the air supply plenum, a small problem can result in it not working properly. So, you can easily check it by temporarily bypassing the switch and seeing if your device turns on or off properly.

In many cases, if the limit switch is the problem, you will still need to call a Batson professional for replacement, but you can avoid a lot of headaches related to tracking down the source of the problem. If you suspect a limit switch problem, make sure to call someone immediately, because it does provide an important safety function and because without it your furnace won’t cycle on and off properly.

Tags: , , , , , ,
Posted in Heating | Comments Off

Common Heat Pump Problems: A Guide from Orangefield

Friday, November 18th, 2011

Heat pumps are great pieces of machinery to have in your Orangefield home, but they are not perfect. They come with their own problems and issues. Usually these can be fixed pretty easily, but it’s good to know what you are looking for.

Below are some common problems encountered by heat pump owners, along with some brief troubleshooting and repair advice. However, for any serious repair job, it is recommended that you call in a professional to fix the problem. This is to ensure the best performance of your heat pump, as well as for your own safety.

  1. No Heat – Obviously, this is a problem. A heat pump should do two things—heat and cool. If it’s not heating at all, something is wrong. Sometimes, this is just a matter of the power supply being interrupted. Press the “Reset” button on the power supply. If that does not fix it, it could be that the power supply has failed or the motor is overloaded.
  2. Incorrect Temperature – For example, you set the thermostat at 72 degrees, but even after several hours, the temperature won’t get over 70 degrees. This can be a problem with the sensor in the thermostat or with the heat pump itself. However, it could also just be the result of very cold temperatures outside. Heat pumps have trouble keeping up when the weather is consistently below 30 degrees Fahrenheit or so, so it may just need help in the form of a supplemental heat supply.
  3. It’s Noisy – Heat pumps are generally designed to run very quietly, so if you notice a lot of noise, there is probably something going on. Common culprits for this type of issue include loose connections, like screws, nuts and bolts. Check for any loose fittings on the heat pump. Also, make sure the contractor who does your annual heat pump inspection tightens these fittings as part of his maintenance routine.
  4. Frozen – This can be indicative of a few underlying problems, but the most common is dirt in the air filter. When filters get clogged, the heat pump can get frosted, ultimately leading to freezing. Check the air filter and make sure to change all air filters regularly.

Heat pumps can experience other issues, but these are some of the more common ones. Generally, though, heat pumps are pretty headache-free machines. Be sure to call a professional repair person is you experience any issues with your heat pump.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Warning Signs of a Broken Furnace: A Tip from Raywood

Monday, November 7th, 2011

How do you know when your furnace is “on the fritz?” There are warning signs of a broken furnace and some are recognizable – but not all. A broken furnace not only deprives your Raywood home of heat and comfort, it also can be deadly, too.

Let’s look at some of the warning signs.

Each year, hundreds of people die and many more are injured from the most common household poison: carbon monoxide. This colorless and odorless poisonous gas comes from several sources and the furnace is the most common source of all; more precisely a broken or malfunctioning furnace. Carbon monoxide is a result of incomplete combustion of a fossil fuel, which is when a fuel does not burn correctly or completely. In a furnace, carbon monoxide gas comes from a poorly operating burner or a cracked heat exchanger. A properly tuned and maintained furnace greatly reduces the risk of carbon monoxide poisoning.

Since carbon monoxide gas is colorless and odorless, it can go undetected. It can make people sleepy and create flu-like symptoms. Sometimes a person may fall asleep and never wake up. But there are warning signs. Drowsiness, vomiting, or flu-like symptoms are a warning sign. Regularly scheduled maintenance of your furnace by a qualified heating and cooling professional and installation of carbon monoxide detectors can reduce the risk of falling ill to carbon monoxide gas.

Another warning sign is a higher energy bill. Sometimes you can’t detect a problem right away because, like carbon monoxide, there may be no obvious signs. Higher utility bills can be a sure sign of a furnace that is working too hard and running more than usual. This may be a result of clogged or dirty air vents, or dirty filters. If your monthly bills are higher than those of the previous year, it may not just be because gas prices are higher.

There are other warning signs of a broken furnace, too. The most obvious is the failure of your furnace to bring your home up to the desired thermostat settings or to maintain an even temperature. Cold or uncomfortable houses are sure signs of a broken furnace. The furnace may cycle on or off, causing an uneven or inconsistent flow of heated air. This can be because of a poor blower or a clogged furnace filter. If you don’t feel any moving heated air or detect any unusual odors or smells coming from your heating vents, that’s a sure sign of a broken or malfunctioning furnace.

A broken or cracked gas line can emit odors and can cause a furnace to malfunction, too.

Don’t take a chance of losing heat and comfort this winter. At the first possible warning sign, call your local heating professional for a heating system tune-up.

Tags: , , , , ,
Posted in Heating | Comments Off